Mazda Forum - Mazda Enthusiast Forums
0 2025/12/14 15:14:33
0 2025/12/14 15:14:13
0 2025/12/13 22:05:12
0 2025/12/13 22:03:47
0 2025/12/13 22:00:31
0 2025/12/08 21:57:10
0 2025/12/08 21:55:02
Hand ground valve stem tip?? I don’t even know what was going on here but it’s crooked and can be seen by the naked eye. It also did not want to pass through the guide.
Hand ground valve stem tip?? I don’t even know what was going on here but it’s crooked and can be seen by the naked eye. It also did not want to pass through the guide.
0 2025/11/18 12:16:50
Interesting valve stem tip wear. The picture makes it look worse than it is, but I’m replacing all with NOS Manley and TRW valves found on eBay either way.
Interesting valve stem tip wear. The picture makes it look worse than it is, but I’m replacing all with NOS Manley and TRW valves found on eBay either way.
0 2025/11/18 12:16:00
Close up of a runny cam bearing
Close up of a runny cam bearing
0 2025/11/18 12:15:37
Head warped like a banana 0.018” in the middle. Gonna have to try to straighten this before even thinking about shaving the head because the cam towers are gonna be warped as well. (I suspect partly the cause of why the cam bearings were toast)
Head warped like a banana 0.018” in the middle. Gonna have to try to straighten this before even thinking about shaving the head because the cam towers are gonna be warped as well. (I suspect partly the cause of why the cam bearings were toast)
0 2025/11/18 12:14:20
After cleaning.
After cleaning.
0 2025/11/18 12:13:42
Before old head gasket removed and cleaned.
Before old head gasket removed and cleaned.
0 2025/11/18 12:12:17
Hand ground valve stem tip?? No idea what’s going on here but it looks dressed with a hand grinder, and did not want to pass through the guide.
Hand ground valve stem tip?? No idea what’s going on here but it looks dressed with a hand grinder, and did not want to pass through the guide.
0 2025/11/18 11:50:15
Closeup of one melted cam bearing
Closeup of one melted cam bearing
0 2025/11/18 11:50:06
Interesting wear on the valve stem tip. The picture makes it seem worse than it is, but I’m replacing all the valves regardless. Was able to find NOS on eBay and grabbed them up.
Interesting wear on the valve stem tip. The picture makes it seem worse than it is, but I’m replacing all the valves regardless. Was able to find NOS on eBay and grabbed them up.
0 2025/11/18 11:49:56
Warped like a banana. 0.018” feeler gauge slides in the middle. Gonna have to try and straighten this before even thinking about shaving the head because the cam towers are gonna be warped too. (Which is partly why I’m thinking the cam bearings were toast)
Warped like a banana. 0.018” feeler gauge slides in the middle. Gonna have to try and straighten this before even thinking about shaving the head because the cam towers are gonna be warped too. (Which is partly why I’m thinking the cam bearings were toast)
0 2025/11/18 11:49:50
0 2025/11/18 11:49:41
Before old head gasket was removed
Before old head gasket was removed
0 2025/11/18 11:49:31
0 2025/11/13 11:39:16
Bought .030 pistons and rings. Plan to overbore. Can feel the area where the rings sat with water in the cylinder.
Bought .030 pistons and rings. Plan to overbore. Can feel the area where the rings sat with water in the cylinder.
0 2025/11/13 11:38:47
Bought .030 pistons and rings. Plan to overbore. Can feel the
Bought .030 pistons and rings. Plan to overbore. Can feel the
0 2025/11/13 11:37:42
0 2025/11/13 11:36:05
0 2025/11/13 11:35:00