too high-accelaration
Thread Starter
|
Junior Member
Joined: Nov 2011
Posts: 9
Likes: 0
too high-accelaration
Hi Folks,
My 1989 323 1.6L sohc 5spd. Has a very high accelaration especially when cold. I have checked the: maf, the tps and throttle body adjustment screw, but nothing helped. Anyone has any idea what could be causing this delema. I even looked for vacuum leaks with no results.
Any help will be appreciated. The car sounds like a F-16 on the tarmack.
Thanks...
My 1989 323 1.6L sohc 5spd. Has a very high accelaration especially when cold. I have checked the: maf, the tps and throttle body adjustment screw, but nothing helped. Anyone has any idea what could be causing this delema. I even looked for vacuum leaks with no results.
Any help will be appreciated. The car sounds like a F-16 on the tarmack.
Thanks...
Thread Starter
|
Junior Member
Joined: Nov 2011
Posts: 9
Likes: 0
Ok, I replaced the engine temp sensor and now what iam getting is the car starts ok, but as it passes the cold mark on gage it goes into an epileptic mode and shuts down. It wasn't doing that prior to the exchange of the ets. Do I need to reset the ECU, I don't know how to do that. I heard you disconnect the ground battery cable, pump the brakes about 10 - 15 times then connect the batt. cable and go for a ride. Do this makes sense to you guys.
Senior Member
Joined: Jun 2011
Posts: 2,389
Likes: 0
From: Midwest
Yes, reset the ECU as you described. Stepping on the brake will turn on the the brake light circuit and drain all voltage that may still be present in capacitors and such.You don't need to pump the brake, just step on it for a few seconds.
It erases the codes in the memory and the ECU starts over on a clean slate. It will have to relearn and self check things. To facilitate that drive normally, include a few highway miles, let it coast to slow down a few times. After a few days it should be up to snug unless something else is not o.k.
If the CEL light comes on please get the code right away.
The best of luck!
It erases the codes in the memory and the ECU starts over on a clean slate. It will have to relearn and self check things. To facilitate that drive normally, include a few highway miles, let it coast to slow down a few times. After a few days it should be up to snug unless something else is not o.k.
If the CEL light comes on please get the code right away.
The best of luck!
Ok, I replaced the engine temp sensor and now what iam getting is the car starts ok, but as it passes the cold mark on gage it goes into an epileptic mode and shuts down. It wasn't doing that prior to the exchange of the ets. Do I need to reset the ECU, I don't know how to do that. I heard you disconnect the ground battery cable, pump the brakes about 10 - 15 times then connect the batt. cable and go for a ride. Do this makes sense to you guys.
Thread Starter
|
Junior Member
Joined: Nov 2011
Posts: 9
Likes: 0
Yes, reset the ECU as you described. Stepping on the brake will turn on the the brake light circuit and drain all voltage that may still be present in capacitors and such.You don't need to pump the brake, just step on it for a few seconds.
It erases the codes in the memory and the ECU starts over on a clean slate. It will have to relearn and self check things. To facilitate that drive normally, include a few highway miles, let it coast to slow down a few times. After a few days it should be up to snug unless something else is not o.k.
If the CEL light comes on please get the code right away.
The best of luck!
It erases the codes in the memory and the ECU starts over on a clean slate. It will have to relearn and self check things. To facilitate that drive normally, include a few highway miles, let it coast to slow down a few times. After a few days it should be up to snug unless something else is not o.k.
If the CEL light comes on please get the code right away.
The best of luck!
Last edited by canbeth29; Feb 19, 2012 at 04:32 PM.
