New ceramic brake pads today

Mazda Forum Mazda Classifieds Photo Gallery Member List Search Contact Us Sponsors
Models Mazda News Mazda Recalls TSBs Timeslips Register Login

New ceramic brake pads today

Printable Version

Mazda >> Mazda Vehicles >> Mazda Tribute >> New ceramic brake pads today

Page: [1]

Message

<< Older Topic Newer Topic >>

New ceramic brake pads today - 9/27/2005 10:02:05 PM

trent1059

Posts: 3
Joined: 9/3/2005
Status: offline

At 76000 miles I noticed a loud grinding noise when I tried to stop quickly, assuming the brakes were worn out I went to the NAPA store and ordered new rotors and ceramic brake pads. it took about 45 minutes to install both sides and bleed the system. super easy job. I hope the ceramic pads will stop the massive amounts of brake dust.
Total cost for rotors and pads..$258 with tax. hope they last but they do have a lifetime warranty if they wear out
The old pads and rotors were worn but I think the would have lasted a while longer, I am impressed that they lasted as long as they did.
Other than oil changes and new tires this is the only maintenance this 03 tribute has had.

Post #: 1

RE: New ceramic brake pads today - 3/5/2006 11:05:11 PM

Luc

Posts: 7
Joined: 3/5/2006
Status: offline

76000 miles...wow ours is at 46000 and needs the front brakes done. What kind of rotors and pads did you get? Also do you remember what size the nut that holds the rotor on was? Was it standard or metric?

Thanks, Luc

(in reply to trent1059)

Post #: 2

RE: New ceramic brake pads today - 3/8/2006 8:46:26 PM

babyhuey

Posts: 2759
Joined: 7/28/2005
Status: offline

76,000 is fairly impressive for first set of front brakes on a Tribute. Hopefully by only service outside of oil changes and tires you do not mean that the transmission oil and rear end oil has not been changed along with things such as air and fuel filters.

You should not need to remove any other nuts or bolts to remove the rotor after taking off the wheel except of the two 7 mm Allen head bolts for the caliper and two 18mm bolts for the caliper mounts. There are sometimes some quick nuts on the lug studs between the wheel and rotor that you will also have to remove in order to get the rotor off.

(in reply to Luc)

Post #: 3

RE: New ceramic brake pads today - 5/4/2006 11:33:16 AM

Nucferr

Posts: 2
Joined: 12/19/2005
Status: offline

Question:
To install just the front pads...Do you have to 'flip up"the caliber. If so which screw do you remove.

Just asking as for a toyota you leave the caliber and just remove two pins. There is alwasy an 'easy trick' to everything

thanks

(in reply to babyhuey)

Post #: 4

RE: New ceramic brake pads today - 5/4/2006 3:46:42 PM

babyhuey

Posts: 2759
Joined: 7/28/2005
Status: offline

Some of the older mazda's had that style with the two pins as well but not in the case of the Tribute. Need to pull the caliper tension spring off first and then remove caps for the upper and lower slides. Both slide pins need to be removed with a 7mm allen wrench and then caliper pulled straight out. Will probably need to push the piston in a bit as well as the pad binds up in the pad path worn into the rotor. Make to check and replace the rotors if needed. Do not think I have ever seen a Trib that needs pads without rotors as well. Too thin of a rotor will not only warp much easier but will greatly increase pad wear due to the rotors inability to disapate heat off fast enough.

Thumbnail Image

Thumbnail Image

Attachment (2)

(in reply to Nucferr)

Post #: 5

RE: New ceramic brake pads today - 5/4/2006 7:18:53 PM

Nucferr

Posts: 2
Joined: 12/19/2005
Status: offline

Thank you baby huey...love pics!

(in reply to babyhuey)

Post #: 6

RE: New ceramic brake pads today - 5/4/2006 8:29:57 PM

babyhuey

Posts: 2759
Joined: 7/28/2005
Status: offline

Welcome Nucferr. I love pics too.

Much easier to show then try and explain. Guess that goes with the old saying " A picture is worth a thousand words". Can't misspel a pic either. doh!! Did it again.